Gourmet New Zealand Itinerary - New Zealand Power Outlet |
Posted: November 5, 2019 |
CEE 7/1 unearthed sockets accept CEE 7/2 round plugs with 4.8 by 19 mm (0.189 by 0.748 in) pins. Because they have no earth connections they have been or are being phased out in most countries. https://www.newzealandmotorhome.com/britz-outbounder/britz-outbounder-2/ permit their use in dry areas. New Zealand power adaptersDo I need a visa for New Zealand?British passport holders can enter New Zealand as a visitor for up to 6 months on arrival without a visa, provided you can satisfy an Immigration Officer that you meet the requirements of the immigration rules. Visitors must have an onward ticket.There are two variants. CEE 7/2 and 7/4 plugs are not compatible with the CEE 7/5 socket because of the round earthing pin permanently mounted in the socket. AustraliaSome multi-standard sockets allow use of several types of plug; improvised or unapproved adaptors between incompatible sockets and plugs may not provide the full safety and performance of an approved socket–plug combination. Plugs and sockets for portable appliances became available in the 1880s, to replace connections to light sockets with wall-mounted outlets. A proliferation of types developed for both convenience and protection from electrical injury. Today there are about 20 types in common use around the world, and many obsolete socket types are found in older buildings.
The unearthed type 21 plug has two rectangular pins, with centres 19 mm apart. The type 23 plug adds a central rectangular earth pin, offset by 5 mm. You can use your electric appliances in New Zealand, if the standard voltage in your country is in between 220 - 240 V (as is in the UK, Europe, Australia and most of Asia and Africa). Manufacturers take these small deviations into account. If the standard voltage in your country is in the range of 100 V - 127 V (as is in the US, Canada and most South American countries), you need a voltage converter in New Zealand. The flat pins for the 10 A version measure 6.25 by 1.55 mm (0.246 by 0.061 in) and 8.0 by 1.9 mm (0.315 by 0.075 in) for the 20 A version, and are set at 30° to the vertical at a nominal pitch of 7.92 mm (0.312 in). The pin length is the same as in the Chinese version. The earthing pin length is 21.4 mm (0.843 in) for the 10 A version and 21.8 mm (0.858 in) for the 20 A version. On the plugs, the pole length is 18.2 mm (0.717 in) for the 10 A version and 17.8 mm (0.701 in) for the 20 A version. The most important difference from the Australian plug is that the Argentinian plug is wired with the line and neutral contacts reversed. These sockets accept plugs of equal or lower current rating, but not higher. For example, a 10 A plug will fit all sockets but a 20 A plug will fit only 20, 25 and 32 A sockets. In New Zealand, PDL 940 "tap-on" or "piggy-back" plugs are available which allow a second 10 A plug to be fitted to the rear of the plug. In Australia these piggy-back plugs are now available only on pre-made extension leads. with non-rewireable CEE 7/7 plugs attached. This plug can be inserted into a Danish Type K socket, but the earth contact will not connect. The earth pin is centred between the apertures, offset by 10 mm (0.394 in). The plug has two round pins measuring 4.8 by 19 mm (0.189 by 0.748 in), spaced 19 mm (0.748 in) apart and with an aperture for the socket's projecting earth pin. This standard is also used in Belgium, Denmark, Poland, the Czech Republic, Slovakia and some other countries. BLACK. POWER SUPPLY CORD, AUSTRALIAN AU1-10P STRAIGHT PLUG, STANDARD STRIPPED ENDS, 6 AMPERE 250 VOLT, 2.5 METERS (8FT.-2IN.) (98") LONG. BLACK. HOSPITAL TYPE (AU1-10P) PLUG AND CLEAR RIGHT-ANGLE IEC 60320 (320) C-13 CONNECTOR, 10 AMPERE 250 VOLT, 2.5 METERS (8FT.-2IN.) (98") LONG. ORANGE CORDAGE.
|
||||||||||||||||
|